How To Repair A Lazy Susan

Download Commodity

Download Commodity

Adjusting misaligned Lazy Susan units might seem intimidating, but the most mutual corrections you lot'll need to make can be done at home using standard tools. Fix rotation bug past adjusting the eye shaft or bottom shelf position. Remedy misaligned doors by correcting the door position from inside the overall unit.

1. 1

   Pinpoint where rotation problems are occurring. When a Lazy Susan becomes stiff and difficult to rotate, the problem is commonly caused by either the center shaft or the position of its bottom shelf. Lightly spin the Susan and annotation where it locks up, has difficulty turning, or has poor clearance.^[1]

   • If the heart movable shelf begins to demark, it will prevent free rotation. In this state of affairs, you'll demand to loosen this shelf.
   • If the round shelves skid downward the center shaft, the bottom shelf can begin to elevate, making it hard to turn. You will need to adjust the height of this shelf to gear up the problem.

2. ii

   Locate the locking bolt to adapt the centre shaft. Look at the tiptop of the center shaft. In that location should be ane large bolt locking the outside shaft to a metallic sleeve positioned inside the shaft. This is the locking bolt for the shaft.^[2]

   • This bolt holds the center shaft in identify and maintains the length of the shaft. Sometimes excess pressure from this bolt can cause the shaft to bind.
   • On some models, the locking commodities might exist located at the bottom of the Susan, however, in most cases, it will institute well-nigh the top.

   Advertisement

3. 3

   Loosen the bolt. If annihilation is within your Lazy Susan, empty it so you take more than space to work. Using a wrench or ratchet, loosen the commodities by turning it one-quarter of a full rotation counterclockwise. At showtime, the bolt may require some elbow grease to break loose.

   • Only loosen the bolt enough to dispense the hardware inside the heart shaft. On some models, this might crave more or less than ane-quarter rotation.
   • By and large, information technology's better to loosen the bolt in minor increments. This will forbid you from loosening it as well much, which could outcome in the alignment of the Susan existence thrown off.

4. 4

   Motion the adjusting rod. Now that the commodities is loose, you lot'll be able to suit the eye shaft. Slide the metal adjusting sleeve the commodities was holding in place no more than 1 inch (2.5 cm) to provide better clearance between the heart shaft and peak of the cabinet.^[3]

   • Piece of work in small-scale increments when adjusting the center shaft. Large adjustments could crusade the Lazy Susan to topple over.

5. 5

   Tighten the bolt to terminate adjusting the center shaft. Utilise your wrench or ratchet to carefully refasten the locking bolt in place. Do not over-tighten the commodities. It should be looser than it was initially, but nevertheless tight enough to hold the adjusting rod in identify.^[4]

6. half-dozen

   Locate the locking screws to conform the shelf position. Almost Lazy Susans should have two or more locking screws located at the center of each shelf. These screws concord the shelves to the eye shaft.

   • When all of the shelves are held together by the front decorative panel, you will need to adjust the entire shelf arrangement. In this instance, there may not be screws located at the height of each shelf.
   • If the shelves must be adjusted separately, y'all'll merely need to work with the bottom shelf. Locate the locking screws in the bottom shelf only.

7. 7

   Loosen the screws. Loosen the locking screws using a Phillips-head screwdriver or similar tool. Hold the screwdriver so its caput meets the fastener directly on. Utilise firm pressure down on the screw while turning counterclockwise to prevent stripping fastener hardware.^[5]

   • Screws can exist left in their holes once they have been unattached from the eye shaft. Even so, yous may want to set loosened screws off to the side to prevent any from getting lost.

8. 8

   Raise the shelves to finish adjusting shelf position. Carefully lift the bottom shelf or entire shelf system until there is roughly one-half an inch (1.25 cm) of space between the bottom shelf and the bottom of the chiffonier.

   • The shelves may resist this adjustment and begin binding on the middle shaft. Maneuver shelves until they are level and at a suitable height.
   • Under no circumstances should you lubricate the center shaft. Doing so could forestall the screws from holding their position.

9. 9

   Tighten the screws. Concur the shelf in place with one hand and utilize your free hand to tighten the locking screws back in place with a screwdriver. Take care not to let the shelf slip as you reattach fasteners, as this could cause information technology to go uneven or binding.^[6]

   • Make the screws every bit tight every bit possible without stripping any of the hardware. The shelves must exist stationary and secure to forbid this kind of misalignment.

Advertisement

1. ane

   Locate where in that location are door problems. Door problems are usually easier to place than rotation issues. The door of the unit may close unevenly or information technology may not have sufficient clearance at the top, bottom, or sides of the cabinet.

   • If the door does not shut completely, or if it closes unevenly, you'll need to adjust the doors until they are centered correctly within the frame.
   • When the top or bottom clearance is insufficient, you lot'll notice the gaps at both sides of the door will exist unequal.
   • When the side clearance is insufficient, the door volition appear kleptomaniacal. Additionally, the gaps effectually it will but unequal.

2. 2

   Loosen the collar screw when doors close unevenly. Open the door and locate the collar at the elevation of the unit of measurement. For many models, this role volition be made of white plastic. Utilise a Phillips-head screwdriver to loosen the screw on this collar.

   • Loosen the screw by one total counterclockwise rotation. Fifty-fifty loosened, the screw should remain in its position in the collar.

3. iii

   Rotate the shelf unit of measurement and door counterclockwise. Using both easily, carefully rotate the unabridged shelf unit and door in a counterclockwise direction. Go on until the neckband hits the catch latch located at the dorsum of the ceiling bracket.^[7]

   • Turn the Lazy Susan slowly. Heed for a slight click. This is a bespeak that yous've reached the catch latch.
   • One time you hit the grab latch, the neckband should be properly aligned with the leap. You lot should feel a slight resistance to boosted counterclockwise turning.

4. 4

   Rotate the door. Gradually rotate the door in a clockwise direction until it reaches the exact center-forepart. If possible, take a step dorsum and check the alignment from a distance. Make sure the door is precisely in place before moving on.

   • The plastic collar should remain fixed in place every bit you rotate the door, so information technology may be difficult to step away. Have a friend or family unit fellow member help you evaluate the door position, in these cases.
   • If you accidentally rotate past the centre-front position, continue rotating the door in a clockwise direction. Do not rotate information technology counterclockwise until after yous finish setting it.

5. five

   Turn the entire assembly. Carefully and slowly rotate the entire assembly in a counterclockwise direction. Keep turning the assembly until the collar screw faces you. The door and collar should maintain their alignment equally you turn the assembly.^[8]

   • It may help you to maintain the position of the collar and door past marking their correct positions with a slice of painter'south tape, masking tape, or something similar.

6. half dozen

   Tighten the screw to finish adjusting uneven doors. Tighten the collar screw back into its original position. The door should now exist properly aligned and fixed into place. Requite the Lazy Susan a few spins to check that everything works correctly, and your door adjustment is finished.^[9]

   • To prevent the collar from twisting out of place while it's attached, you may need to hold it in place as the spiral is tightened.

Advertisement

1. 1

   Remove the retainer prune to improve top and bottom clearance. Locate the plastic retainer clip at the bottom of the eye shaft. Firmly grasp the clip between your fingers, open it, and pull it out. Under the prune should be a cut-out portion of the shaft with a thumbscrew adjustment bike.

   • The chiffonier will need to exist completely empty when y'all make this adjustment. Practice not attempt to complete the procedure when the shelves are loaded, specially if they are heavily loaded.

2. 2

   Turn the adjustment wheel. Employ your fingers to turn the thumbscrew adjustment wheel in the cutting-out portion of the center shaft. Rotate the wheel clockwise to raise the door and counterclockwise to lower the door.

   • Generally yous can look that for each full rotation of the screw the tiptop volition exist adapted past about 1/32 in (0.8 mm).
   • You may need to apply gentle pressure to the underside of the bottom shelf to aid the adjustment if you are attempting to raise the door.^[10]

3. 3

   Supercede the retainer prune to complete the elevation and lesser adjustment. Afterward adjusting the door to the proper height, return the retainer prune to its original position at the bottom of the pole. The prune should fasten back into place firmly.^[11]

   • It's a good idea to tighten all of the aligning screws fastened to the center shaft, shelves, and door subsequently setting the superlative. Doing this could forestall the door from falling out of alignment once more.

4. 4

   Outline the elevation and bottom brackets when side clearance is insufficient. Using an erasable pencil, lightly outline the current position of the tiptop and lesser brackets. If lighting is also poor inside the cabinet to make these marks easily, use a flashlight or electrical lantern.

   • Doing this will requite you a reference point to work from as y'all make the adjustment. Pencil marks tin can be erased in one case you complete the process.

5. 5

   Realign the pivot pole from the top. Use a screwdriver to remove the setscrews and loosen the star washers holding the pivot housing in place on both sides of the pivot pole. Suit the pivot housing and pin pole until both are centered and aligned.^[12]

   • When the star washers are in place but before fastening the setscrews, take a pace back and look over your Lazy Susan. If the side clearance is still uneven, remove the washers and readjust the pivot.
   • Use your outline to guide your adjustments. For example, if the left side is depression, you'll likely need to movement the pivot pole and housing to the correct.

6. six

   Refasten the pivot housing. Once you tighten the star washers, you'll exist ready to return the setscrews to their original position. When the screws are in place, check the side clearance of the Lazy Susan once again to make sure that it wasn't altered as you refastened its hardware.^[xiii]

   • This adjustment may take care of your side clearance problem. If the lower half of your Susan appears to exist misaligned, you lot'll accept to adjust the pivot base of operations in add-on to its superlative.

7. vii

   Realign the pivot base when necessary. Open the door broad enough to expose the bottom bracket on either side of the Susan. Loosen this subclass past removing the fastening setscrew and star washer with a screwdriver. Now you can realign the pivot cam (metallic arm) base so that it's centered.^[14]

   • You'll have to repeat this procedure on the opposite side of the Lazy Susan where yous'll notice an identical bracket/pivot cam base.
   • Piece of work on brackets one at a time. Afterwards you've taken autonomously, realigned, and refastened the beginning bracket, move on to the next one.
   • When properly centered, the pivot cam bases of both sides should exist aligned with regard to the centre pole.

8. 8

   Refasten the bracket. Be careful when refastening; if you jostle the pivot cam, it could be knocked out of alignment. Supplant the star washers and reattach the setscrews for the bracket. When fastened, similarly adjust the reverse side bottom bracket/pivot cam base of operations.

   • Verify that the position did non become altered while you were returning these pieces to their original positions past stepping back and evaluating the evenness of the side clearance.

9. nine

   Check the door to consummate your side clearance adjustment. Sometimes these alignments (specially those made to pivots) tin can crave several attempts before they are resolved. Double check door alignment later on completing the tiptop and lesser adjustments, especially.^[fifteen]

   • If the side clearance is withal unequal, you will need to readjust the elevation pivot pole and/or bottom pivot cams.

Advertising

Add New Question

• Question

  How do I tighten a Lazy Susan that keeps turning around and effectually? Information technology won't lock in place.

  

  There is a plastic clasp at the top of the Lazy Susan. You lot will see a notch in information technology that should catch so that it holds the unit in place. Commonly, the older units will show the plastic to be worn. Merely replace the plastic piece, and it should realign and close properly.

• Question

  What shelf do I put the heavy items on, top or bottom?

  

  Putting the heavy items like canned goods on top volition increment the chances of the shelf breaking, then put heavy stuff not the lesser instead. The pinnacle shelf is improve for boxes of pasta and bags of rice.

• Question

  How do I fix set screws that won't tighten?

  

  If the screws for your Lazy Susan don't tighten, the fasteners or the attaching hardware may be stripped. This means that damage has been washed to the function of the hardware intended to grip the fastener (like the grooves of a screw). Supercede stripped hardware and try again.

• Question

  How tin can I adjust a bottom corner cabinet lazy susan that has the chiffonier door fastened?

  

  If you accept the one with a cam at the top of the center pole and a screw with a leap, then adjusting the screw on the side that has a spring on it volition adjust how the outer surface of the lazy susan "door" aligns with the rest of the cabinets. Don't be afraid to tighten all the way or loosen as far as possible. From what I can tell, the screw will non come out. I turned the spiral in and thought I counted the turns. And so backed it out again the same amount of turns and all all of a sudden the door was more than than an inch out of alignment. I had to dorsum it out a lot further to reset the alignment.

• Question

  How do I fix a lazy Susan if the shelf adjuster barbarous and took the shelf with it? There is not enough room to adjust it and the flange is crooked.

  

  If the shelf adjust fell and knocked a shelf out, dissentious the shelf flange, you may need to completely disassemble the shelf, replace the damaged hardware (inexpensive flanges tin can be bought at near hardware stores), and so reinstall the Lazy Susan.

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Advertising

Thanks for submitting a tip for review!

Things Y'all'll Need

• Eraser
• Flashlight (or electric lantern for calorie-free; optional)
• Pencil
• Phillips-caput screwdriver
• Standard screwdriver
• Wrench (or ratchet set up)

About This Article

Article Summary X

If you lot're having problems with your Lazy Susan, you lot should be able to accommodate it using standard tools. Before you brand any adjustments, empty the cupboard and then y'all take space to piece of work. If the shelves are stiff when you turn them, loosen the locking commodities at the top of the heart shaft with a wrench or ratchet, then motility the adjusting rod an inch, and tighten the bolt. To fix the shelf height, unscrew the locking screws on the central shaft that hold each shelf, adjust the peak, then tighten the screws again. If the doors are misaligned, use a Philips-head screwdriver to loosen the spiral at the top of the doors, rotate the shelf unit and door counterclockwise until the top hits the latch, so rotate the door clockwise until it reaches the eye. For more than tips, including how to arrange the clearance inside your Lazy Susan, read on!

Did this summary help you?

Thanks to all authors for creating a page that has been read 174,382 times.

Did this commodity help you?

Source: https://www.wikihow.com/Adjust-a-Lazy-Susan

Share this post